# LED ring board — JLCPCB assembly (SMD-only vs full)
> **Out of date in part (2026-11-13):** `CP1` is now the SMD C72470 and `J1`/`J2` are JST VH/XH; see `README.md`. The rest is the 2026-09 comparison.

Generated by `tools/build_jlc_assembly.py` (re-run after any board change — CPL
positions are read live from `LEDRing.kicad_pcb`).

## 2026-09-10 — full assembly, 0 sourcing-risk, no board changes

The board is 357 SMD parts (178× SK6812, 178× 100nF, R1) plus **2 THT parts**
(CP1, J1). Both THT parts substitute to in-stock JLCPCB wave-solder parts whose
footprints already match the board, so **full assembly needs zero hand-soldering
and no re-layout**:

| Part | Now | JLCPCB/LCSC # | Assembly |
|---|---|---|---|
| `CP1` 1000µF radial (D10/P5) | CX 1000µF 16V, D10×13, 5mm pitch | **C439782** | Wave-solder |
| `J1` Molex 5569-06A2 (2×3 R/A) | Molex 39301060 right-angle 4.2mm | **C114098** | Wave-solder |

`J1` mates the mainboard's `J5` through the 6-conductor Mini-Fit crimp harness.

## The two upload sets

| For a quote of… | BOM | CPL |
|---|---|---|
| **SMD-only** | `LEDRing_BOM_SMD.csv` | `LEDRing_CPL_SMD.csv` (357) |
| **Full assembly** | `LEDRing_BOM_FULL.csv` | `LEDRing_CPL_FULL.csv` (359) |

## Stock (verified on jlcpcb.com, 2026-09-10)

| Part | JLCPCB # | In stock | Need/board | Tier |
|---|---|---:|---:|---|
| SK6812 | C5378720 | 90,792 | 178 | Extended, **Standard only** |
| 100 nF 0603 | C14663 | 39,665,055 | 178 | Basic |
| 470 Ω 0603 | C23179 | 7,624,838 | 1 | Basic |
| CP1 1000 µF | C439782 | 40,535 | 1 | Extended |
| J1 Molex 5569 | C114098 | **2,352** | 1 | Extended |

All ample. **`J1` (2,352) is the lowest** — still fine at 1/board, but it's a genuine
Molex part and the one to re-check if you order a large batch or come back months later.

Note the **SK6812 is "Standard PCBA only" + high assembly difficulty**, so this board
can't run on the cheaper Economic tier regardless of the THT question.

Since 2026-11-08 every part is on the top side, so the order is a **single-sided** Standard assembly
(setup $25.56 and stencil $8.21 instead of $51.12 and $16.42 for two sides).

Since 2026-11-08 the LEDs are the SKC6812RV (C2890040, 83,968 in stock); its tier is not checked yet.

## Before ordering
- **1oz copper** (JLCPCB's default) since 2026-11-09, with the 7.5 A fuse in the 5 V harness; the mainboard stays at 2oz.
- Order the correct **LED pinout** part — `C2890040` (and `C5378720` before it) was verified against the
  real datasheet (pin1=GND, pin2=DIN, pin3=VDD, pin4=DOUT); re-verify if substituted.
- Run JLCPCB's Upload-BOM tool for a final live stock/price check.

*LCSC/JLCPCB numbers verified 2026-09-10 on their live pages; JLCPCB re-validates at upload.*
