# JLCPCB assembly — SMD-only vs full-assembly cost comparison

Generated by `tools/build_jlc_assembly.py` (re-run after any board re-layout —
CPL positions are read live from `Mainboard.kicad_pcb`).

## 2026-09-10 — every part is now JLCPCB-assemblable (0 sourcing-risk)

The 8 parts previously flagged as sourcing-risk were all substituted with
in-stock, JLCPCB-assemblable parts, so **full assembly needs zero hand-soldering**:

| Was (risk) | Now | JLCPCB/LCSC # |
|---|---|---|
| `J1-H1`,`J1-H2` 1×20 female socket | Ckmtw B-2200S20P-A120 (wave-solder); Kinghelm KH-2.54FH-1X20P-H8.5 since 2026-11-08 | C124410, now C2905423 |
| `J6-J1`,`J6-J3` 1×22 female socket | **split** to 1×20 (C124410) **+** 1×2 (C124411) each; one Hong Cheng 1×22 per row since 2026-11-08 | C41376161 |
| `J-PWR-IN` Molex 5566 2×4 | HCTL HC-5566-2*4A-05 (4.2mm, 9A/pin) | C20539149 (split on 2026-10-17 into `J-PWR-5V`, HC-5566-2*2A-05, C20539147, and `J-PWR-12V`, JST B2B-XH-A, C158012) |
| `J5` Molex 5566 2×3 | HCTL HC-5566-2*3A-05 (still mates the ring board) | C20539148 |
| `F1` blade holder | **2× T508VS** SMD blade clips `F1A`+`F1B` (L = 19.04mm between the single pads' outer edges, per XFCN's drawing) | C41371869 |
| `F3` blade holder | **2× T508VS** SMD blade clips `F3A`+`F3B` (same layout) | C41371869 |

Board re-placed + re-routed after the swaps — **0 unconnected, 0 DRC violations**.
T508VS footprint pulled from EasyEDA (`easyeda2kicad`) — the exact one JLCPCB uses.

**User-supplied (not on the BOM, like the plug-in modules):** the blade fuses
themselves (F1 = 2A, F3 = 15A, standard/low-profile ATO) drop into the clip
pairs; the ESP32-S3-ETH, DevKitC-1, and TMC2209 modules plug into their sockets.

## The two upload sets

| For a quote of… | BOM | CPL |
|---|---|---|
| **SMD-only** | `Mainboard_BOM_SMD.csv` | `Mainboard_CPL_SMD.csv` |
| **Full assembly** | `Mainboard_BOM_FULL.csv` | `Mainboard_CPL_FULL.csv` |

`assembly_cost_compare.csv` is the per-part rollup.

## Counts (as of 2026-10-25, counted by `build_jlc_assembly.py`; the twelve test points are not in either BOM)

| Metric | SMD-only | Full (SMD+THT) |
|---|---:|---:|
| Placed components | 77 | 100 |
| Solder joints | 235 | 397 |

The T508VS fuse clips were removed on 2026-10-21: `F1` is now one resettable PTC and `F3` is gone, so the counts above contain no clips. The full-vs-SMD delta is the
THT joints (module sockets, power connectors, regulator, bulk capacitor, headers) —
all now machine-assemblable.

## Every part now has a verified LCSC # (0 "select")
The generic THT headers that were previously unpinned are now concrete, in-stock,
JLCPCB wave-solder parts:

| Part(s) | Now | JLCPCB # |
|---|---|---|
| `J2-MODE`,`J2-MOTOR` 1×08 female | HCTL PM254-1-08-Z-8.5; JXTCONN PM2.54-1X8PM-H85 since 2026-11-08 | C2897371, now C42431840 |
| 7× encoder headers 1×05 male | JXTCONN PH2.54-1X5P-H25 | C42431835 |
| `J-BTN-TAP` 1×02 male | JXTCONN PH2.54-1X2P-H25 | C42431798 |
| `C6` 220 µF (D8/P3.5) | Rubycon 35ZLH220MEFC8X11.5 (was SamYoung NXH35V220M8×11.5, C346959, 375 in stock; same ripple and impedance ratings); since 2026-11-08 an SMD 100 µF/35 V Lelon, the `C8`/`C11` part | C107639, now C176683 |
| `D1` 1N5822 (DO-201AD) | LRC 1N5822 | C82806 (replaced on 2026-10-18 by the SMA SS34, C8678) |
| `U2` 12V→3.3V reg | TRACO TSR 2-2433N (2A, SIP-3 14×7.6mm; replaced the 1A TSR 1-2433E on 2026-09-29) | C45406999 |

## Before ordering
- **2oz copper** on the order form (LED-ring current path; not encoded in gerbers).
- **Blade-fuse fit, checked 2026-09-30:** XFCN's T508VS drawing gives the two-clip layout as
  L = 19.04mm (standard/low-profile ATO) **between the outer edges of the clips' single
  pads**, single pads outboard. Until 2026-09-30 the board had 19.04mm between the clip
  *origins* (23.6mm edge to edge). With Littelfuse's ATO blades (outer edges 14.5mm apart,
  4.1mm gap, so 9.3mm centre-to-centre), that put the grips ~13.9mm apart and no standard
  fuse could span them. All four clips moved 2.28mm inward, so the edges are now 19.04mm apart.
  A mini (ATM) fuse would need L = 14.27mm, so use **standard or low-profile ATO** only.
  The 30A clip rating covers `F3`'s 15A.
- **Low-stock parts to watch** (JLCPCB in-house stock, adequate for small runs but
  worth confirming quantity at upload): T508VS `C41371869` ~310,
  `J2` `C124416` ~558, `C6` `C346959` ~593, `D1` `C82806` ~800. `U2`, the TSR 2-2433N
  `C45406999`, is a *candidate*: its stock wasn't shown on JLC's page, so confirm it at
  upload (the plain TSR 2-2433, LCSC C5357116, had only a handful in stock and its
  centred body collides with `D1`, so it isn't a drop-in fallback). Pinout (Vin/GND/Vout)
  checked against Traco's TSR 2N datasheet.
- Run JLCPCB's **Upload BOM / Smart-BOM** tool for a final live stock/price check.

Added since: `C8` 100µF/35V SMD electrolytic, Lelon VZH101M1VTR-0607, **C176683** (Extended, confirm stock), and `C9` 0.1µF 0603, **C1590**.

*LCSC/JLCPCB numbers verified 2026-09-09/10 on their live pages (C8 2026-09-27); JLCPCB re-validates at upload.*
