Tinkercad files
The case and the motor mount as separate parts, in millimetres, ready to import into Tinkercad (Import, then choose a file). Download everything in one go below, or take single parts from the table.
Download all (ZIP)
tinkercad_files.zip
24 files, 589 KB. Every STL and the plate outline (SVG and DXF), plus PLACEMENT.txt with the size and position of each part.
Untested in Tinkercad itself. The meshes are closed and the sizes match the design, but I could not open them in Tinkercad. Tinkercad has no box for typing absolute positions, so place parts by eye with the Ruler and Align tools, or import enclosure_cutaway.stl, which is already assembled.
How the coordinates work
- Units are millimetres.
- The box frame has its origin at the outer front-left corner of the box, on the underside of the floor; x runs to the right, y toward the rear, z up.
- Most parts are exported already in that frame, so the position in the table is where their minimum corner sits. The mount parts (plate, standoff, motor) are exported at their own origin; the table says where to place them.
Assembled
| File | What it is | Size x, y, z (mm) | Place min corner at (x, y, z) | Download |
|---|---|---|---|---|
| enclosure_cutaway.stl | Everything except the lid, platter, knobs and the front and right walls, in one piece. Start here. | 349.0 x 289.7 x 102.2 | 0.0, 0.0, 0.0 | STL3.4 MB |
Case and fittings
| File | What it is | Size x, y, z (mm) | Place min corner at (x, y, z) | Download |
|---|---|---|---|---|
| enclosure_case.stl | Floor and three walls (the backplate is the fourth), with the backplate grooves and the right wall's exhaust slots. | 349.0 x 284.4 x 74.9 | 0.0, 0.0, 0.0 | STL30 KB |
| enclosure_lid.stl | 6 mm lid with the 8 in platter opening, the three ball-unit holes and four screw holes. | 349.0 x 284.4 x 6.0 | 0.0, 0.0, 74.9 | STL226 KB |
| enclosure_backplate.stl | 2 mm aluminium backplate, inset in grooves and screwed to the rear corner blocks: connector cutouts, earth stud, screw holes and vents. | 343.0 x 2.0 x 74.9 | 3.0, 278.0, 3.0 | STL2.7 MB |
| enclosure_io_connectors.stl | IEC inlet and two D-size connectors, envelopes only. | 135.0 x 51.7 x 31.0 | 29.7, 238.0, 18.5 | STL12 KB |
| enclosure_tray.stl | Ring heat plate (the LED tray), thermal pad, ring board, LED field and the four lid standoffs. | 203.2 x 203.2 x 23.0 | 40.4, 40.4, 51.9 | STL180 KB |
| enclosure_platter.stl | 10 in platter with its hub boss. | 254.0 x 254.0 x 14.3 | 15.0, 15.0, 76.2 | STL115 KB |
| enclosure_knobs.stl | Four knobs and the big button. | 34.0 x 172.0 x 15.0 | 294.7, 40.9, 80.9 | STL111 KB |
| enclosure_blocks.stl | The four 10 mm corner blocks the lid screws into (one file, four bodies). | 337.0 x 272.0 x 68.9 | 6.0, 6.0, 6.0 | STL6 KB |
| enclosure_balls.stl | The three flanged ball units that carry the platter (hole size is a placeholder). | 191.7 x 219.1 x 10.3 | 75.7, 32.5, 73.9 | STL462 KB |
Motor mount
| File | What it is | Size x, y, z (mm) | Place min corner at (x, y, z) | Download |
|---|---|---|---|---|
| enclosure_motor.stl | Motor, plate, four standoffs, coupler and the D-flat stub, assembled. | 55.0 x 55.0 x 96.2 | 114.5, 114.5, 6.0 | STL347 KB |
| motor_plate.stl | The 3 mm plate, 10 holes. Exported at its own origin (shaft axis at x = y = 0). | 55.0 x 55.0 x 3.0 | 114.5, 114.5, 46 | STL237 KB |
| motor_standoff.stl | One hex standoff; make four. Own origin. | 6.4 x 5.5 x 40.0 | 114.8, 115.3 / 162.8, 115.3 / 114.8, 163.3 / 162.8, 163.3, all at z 6 | STL3 KB |
| motor_nema17.stl | NEMA17 body, pilot and shaft. Own origin. | 42.3 x 42.3 x 44.5 | 120.9, 120.9, 24.5 | STL54 KB |
Other parts
| File | What it is | Size x, y, z (mm) | Place min corner at (x, y, z) | Download |
|---|---|---|---|---|
| enclosure_fan.stl | 120 mm fan. | 120.0 x 120.0 x 25.0 | 185.7, 137.9, 6.0 | STL61 KB |
| enclosure_psu.stl | RD-85A power supply, turned. | 97.0 x 159.0 x 39.5 | 12.7, 47.9, 6.0 | STL4 KB |
| enclosure_pcb.stl | Main PCB with module envelopes. | 116.0 x 100.0 x 26.1 | 217.7, 29.9, 12.0 | STL13 KB |
Flat outlines
| File | What it is | Size x, y, z (mm) | Place min corner at (x, y, z) | Download |
|---|---|---|---|---|
| motor_plate.svg | Motor plate outline with holes. Import as a 2D shape and extrude 3 mm. | flat | - | SVG7 KB |
| backplate.svg | Backplate, seen from outside. Import as a 2D shape and extrude 2 mm. | flat | - | SVG77 KB |
| ring_plate.svg | Ring heat plate, seen from the board's LED side. Import as a 2D shape and extrude 3.175 mm. | flat | - | SVG1 KB |
| motor_plate.dxf | The motor plate as DXF, for laser, waterjet or CNC cutting. | flat | - | DXF23 KB |
| backplate.dxf | The backplate as DXF (seen from outside, mm). | flat | - | DXF257 KB |
| ring_plate.dxf | The ring heat plate as DXF (seen from the LED side, mm). | flat | - | DXF1 KB |