Uncle Magic's Liquid Turntable: Hardware Overview#
How the turntable is built: what the parts are, how they are connected, how power flows, and what protects what. For operating it, see the User Guide. For exact pin-by-pin detail, see the README; for the reasoning behind design decisions, the detailed README; for their history, the changelog; the KiCad files in kicad_mainboard/ are the authority on connections.
1. System overview#
The turntable is built from two printed circuit boards, a stepper motor and the panel controls, fed by one external 5 V / 12 V supply.
| Part | What it is |
|---|---|
| Mainboard | 100 × 100 mm board that carries three plug-in modules, the motor driver, the power protection and every connector. It is the brain of the unit. |
| LED ring board | A second board in this repository: 178 addressable LEDs on an 8 inch (203 mm) board with a centre hole. It is fixed near the top of the case and does not turn with the platter (section 6). |
| Stepper motor | A NEMA 17 bipolar stepper, joined directly to the platter by a flexible shaft coupler. No gearbox. |
| Panel controls | Four rotary encoders (with push buttons) and a tap button, wired to the mainboard through small headers. There is no separate panel board. |
| Power supply | One 5 V / 12 V supply (Mean Well RD-85A): 12 V for the motor, fan and electronics, 5 V for the LEDs. Outside the board. |
Three computers share the mainboard, all running at 3.3 V:
| Module | Role |
|---|---|
| Waveshare ESP32-S3-ETH | The main controller. Runs this project's firmware: tempo, speed control, web pages, OSC, encoders. Has wired Ethernet (W5500) and Wi-Fi. |
| BigTreeTech TMC2209 (stepper driver module) | Drives the motor coils. Configured over a one-wire serial link. |
All three are socketed: they plug into female headers, so each can be replaced or reflashed.
Power flow#
Signal flow#
Platter support and bearings#
The platter is a 10 in (254 mm) by 1/4 in acrylic disc, about 380 g, turning at 17 RPM at most. The motor only drives it: the platter's weight is carried on three inexpensive flanged ball units pressed into the lid (flange on the lid top, ball about 3 mm above it), and the drive is a sliding joint. A 5 mm D-flat stub is clamped in the flexible coupler's top end, and the platter's hub slides on it with at least 10 mm engaged, so the shaft's height never holds the platter up (it can be about 4 mm too high or 8 mm too low). The enclosure notes (enclosure/MOTOR_MOUNT.md) have the dimensions and the sketch; the ball units, the hub and the stub are untested.
2. The mainboard#
| Size | 100 × 100 mm, two copper layers, 1.6 mm, 1 oz copper (JLCPCB's default; see section 8). |
| Mounting | Four M3 holes (3.2 mm) at the corners. |
| Design tool | KiCad 10 (kicad_mainboard/Mainboard.kicad_pcb) |
| Schematic | A one-page index plus six function sheets, below. PDF: Mainboard_schematic.pdf |
Schematic sheets#
| Sheet | Contains |
|---|---|
| Power | The two power inputs J-PWR-5V and J-PWR-12V, the 12 V resettable fuse F1, diode D1, TVS diode D5, bulk capacitors and the reverse-polarity FET Q5. There is no 3.3 V regulator on the board: the ESP32-S3-ETH module makes +3V3. |
| Controller | Sockets for the ESP32-S3-ETH (J1-H1, J1-H2; VSYS fed from +5V_LED_LOGIC, +3V3 taken from the module) and the boot-strap pull-up R23. |
| Motor | Sockets for the TMC2209 (J2-MODE, J2-MOTOR), the UART resistor, and the motor connector J3. |
| LED | The ring data and clock buffers U3 and U5 (3.3 V to 5 V), their supply diode D33, the ring signal connector J-LED-SIG (which also brings in the ring's temperature sensor: D34, R65, R66, C16 to GPIO3) and power connector J5 with its TVS D32, and the fan header J-FAN with its PWM inverter Q6. |
| Panel IO | The TCA9555 I/O expander U1, its I2C pull-ups, and every encoder and button header. |
| Test points | TP1 to TP13, the probe pads listed in section 3. |
Module orientation#
Each module fits its socket only one way up. The board is silkscreened to match, but a module plugged in backwards would put power on the wrong pins.
| Module | How it goes in |
|---|---|
| ESP32-S3-ETH | RJ45 side up, with the RJ45 and USB-C end at the top edge of the board. The 72.8 × 21 mm module overhangs the board edge by about 16 mm, which is where the network socket and USB port are reached. |
| TMC2209 | Rotated 180° from the usual drawing: EN and VM at the bottom (panel-header edge), EN column on the right, VM column on the left. Check the module's own silkscreen first; a reversed module will be destroyed. |
Key parts#
| Ref | Part | Job |
|---|---|---|
U3 | 74AHCT1G125 | Lifts the LED data signal from 3.3 V to 5 V |
U1 | TCA9555PWR (TSSOP-24) | I2C input/output expander (address 0x20), fixed 100 k pull-ups on its inputs (the firmware also drives an MCP23017, for older boards) |
D1 | SS34 Schottky (SMA) | Stops reverse 12 V and stops motor energy flowing back |
D5 | SMBJ15A | Clamps voltage spikes on the 12 V rail (about 24 V at its rated surge current) |
D4 | PESD3V3S1UL | Static-discharge protection on 3.3 V |
Q5 | SP30P03NK (P-channel FET) | Blocks a reversed 5 V feed on the ring line |
D32 | SMBJ5.0A | Clamps spikes on the ring's 5 V |
D33 | SS34 Schottky | Feeds +5V_LED_LOGIC (the two LED buffers and the module's VSYS, so all of the 3.3 V logic) from the 5 V input and blocks a reversed supply |
D34, R65, R66, C16 | PESD3V3S1UL, 10 k 1 %, 1 k, 100 nF | Ring temperature input: ESD clamp and pull-up at J-LED-SIG pin 5, then a 1 k / 100 nF filter into GPIO3 |
Q6 | 2N7002 | Inverts the fan PWM signal |
F1 | 2 A hold resettable fuse (PTC), 1812 | Soldered on; trips at about 3.5 A and resets once the fault is gone and it has cooled |
C6 | 100 µF 35 V (SMD, same part as C8/C11) | Bulk capacitor on the 5 V input; the ring has its own 1000 µF CP1 at its connector |
C8, C11 | 2 × 100 µF, 35 V | Bulk capacitance for the motor driver |
R23 | 1 k | Holds the motor-driver enable pin high (driver off) during boot |
R26, R62 | 10 k | Keep the LED data and clock lines low while the ESP32 starts, so the ring doesn't flash |
U3, U5 | 74AHCT1G125 | Lift the ring's data (GPIO18) and clock (GPIO2) from 3.3 V to 5 V |
R63, R64 | 33 Ω | Source resistors at the buffer outputs, to damp the signal cable |
R27 | 4.7 k, 1206 | Bleeder across the 12 V capacitors so the rail drains after power-off |
3. Power#
Rails#
| Rail | Source | Feeds | Protection |
|---|---|---|---|
| +12V_MOTOR | 12 V supply via J-PWR-12V | Motor driver supply; fan header J-FAN (about 0.1 A) | F1 2 A fuse; D1; 200 µF bulk; D5 TVS; R27 bleeder |
| +3V3 | The ESP32-S3-ETH's own JW5060 buck, from VSYS = +5V_LED_LOGIC | ESP32-S3-ETH, TMC2209 logic, TCA9555, encoder pull-ups, the ring NTC pull-up | The buck limits its own current; D4 is static protection only |
| +5V_LED_RING | 5 V supply via J-PWR-5V pins 1 and 3 | LED ring; through D33 (from before Q5) the LED buffers U3/U5 and the module's VSYS, so all of the 3.3 V logic | 7.5 A blade fuse in the harness at the supply; Q5 reverse-polarity FET; D32 TVS |
The three rails do not share a protection path: a fault on one cannot ride through into another. The 12 V supply feeds only the motor driver and the fan. The 5 V supply feeds the LED ring and, through D33, the logic: the two signal buffers and the module, whose own regulator makes +3V3 for everything else.
Design choices worth knowing#
- 3.3 V comes from the ESP32-S3-ETH module itself. On the module,
VSYSfeeds a JoulWatt JW5060 buck (4-18 V in, 3 A, fixed output); its enable (3V3_EN) is pulled up toVSYSby the module'sR67. The board feedsVSYS(J1-H1pin 2) from+5V_LED_LOGIC, about 4.7 V afterD33, leaves3V3_EN(pin 4) open, and takes+3V3from the module's3V3pin (pin 5). This replaced the board's own 12 V to 3.3 V converter (U2, K7803-2000R3) and its capacitorsC12-C14: about $2.40 to $3.40 less per board, the part with the least stock gone, and no 17.5 mm tall part. - The 3.3 V rail has headroom. The ESP32, the W5500 and a few milliamps of logic run from it, well under 1 A against the buck's 3 A; the main board's Wi-Fi power is still capped at 15 dBm as a conservative setting.
- USB-C powers the logic. USB VBUS reaches
VSYSthrough the module's 1N4148, so the module's USB-C can run the ESP32, the expander and the encoders on its own for flashing and setup (not the motor or the ring), and our 5 V never reaches a USB host. With the 5 V supply on as well, it wins (about 4.7 V against USB's 4.3 V after the 1N4148). - The logic needs the 5 V supply. With 12 V on and 5 V off, the TMC2209 has motor power but no VIO; the datasheet holds its logic in reset with the bridges off below the VIO threshold. Check it once on the bench.
- Switch-off behaviour. Without
R27the 12 V capacitors would linger at a few volts and leave the processors in brown-out. With it the rail is under 1 V in about 2.5 seconds. - Switch-on order. 3.3 V comes up with the 5 V rail; 12 V may arrive at any time; the worst case is a few milliseconds of 3.3 V on the data buffer's input before it has power, limited to about 10 mA by
R18.
Power budget#
| Rail | Typical | Worst case |
|---|---|---|
| 3.3 V logic | 0.3 to 0.45 A, Wi-Fi off | About 0.7 A, Wi-Fi on (2 A available) |
| 12 V motor and fan | The motor runs at 800 mA per phase; about 0.5 A from the supply | F1 holds 2 A (less when hot) |
| 5 V ring | Depends on colour and brightness; the LED engine holds each LED to 36.6 mA and the ring to about 4.5 A | A single colour at full brightness about 3.2 A (18 mA × 178); white would be 9.6 A at the full current field (31) without the limits, which must never be lifted |
Mains side: two switch-mode supplies together draw about 100 to 120 W in steady state, with a 20 to 60 A inrush for a few milliseconds at switch-on. A slow-blow fuse and a switch rated at 10 A or more are recommended.
Power connectors J-PWR-5V and J-PWR-12V#
The two supplies come in on two different connectors, so a 12 V plug cannot be put into the 5 V header.
J-PWR-5V: Molex Mini-Fit Jr, 4 positions (2 × 2). The 5 V is on two pins because of the ring current (about 3.3 A each at full white, 2.3 A at the LED engine's limit).
| Pin | Net | Pin | Net |
|---|---|---|---|
| 1 | +5V | 2 | GND |
| 3 | +5V | 4 | GND |
J-PWR-12V: JST XH, 2 positions (B2B-XH-A, 3 A; plug housing XHP-2 with SXH-001T-P0.6 terminals, wire 22 to 28 AWG). Pin 1 is +12 V and pin 2 is GND, as printed on the board. A different connector family from the 5 V input, so the two cannot be swapped.
Both connect ahead of the fuses. Never plug or unplug either with power on.
The supply (Mean Well RD-85A)#
The chosen supply is the Mean Well RD-85A, one dual-output unit that gives both rails. The board needs 5 V for the LED ring only (about 6.5 A at full white, 7.3 A at the LEDs' maximum drive current, 4.5 A with the LED engine's current limit) and 12 V for everything else (about 2.5 A worst case), about 70 W together. Prices below are from retailer listings on 2026-10-07 and were not verified; check stock and the datasheet before ordering.
| Option | 5 V | 12 V | Approx. price | Notes |
|---|---|---|---|---|
| Mean Well RD-85A (chosen) | 8 A rated, 10 A range | 4 A rated, 5 A range | $27-41 | One box, one mains connection. The only limit on the ranges is total power (88 W), and the board's worst case is about 70 W; the ring's full white (6.5 A) is inside the 8 A rating. |
| Alternative: Mean Well LRS-75-5 plus LRS-35-12 (two supplies) | 14 A | 3 A | about $30 | Full ring current with margin; two boxes and a split mains feed behind the single switch. |
| Alternative: Mean Well MD-100S (about 100 W dual output) | 10 A | 4.2 A | not found | Similar to the RD-85A with a little more headroom. |
Do not use the RD-85B: it is 5 V / 24 V. The board's motor rail is 12 V.
RD-85A points from Mean Well's specification (RD-85-SPEC, 2024-11-22):
- No minimum load. The spec only recommends loading 5 V above 10 % (0.8 A) to hold its +/-2 % tolerance. With the ring dark the 5 V output may sit slightly high, inside its 4.75 to 5.5 V range. The ring does not mind.
- Tolerance and ripple: 5 V +/-2 %, 80 mVp-p; 12 V +/-5 % (11.4 to 12.6 V), 120 mVp-p. The 12 V rail is well inside
D5and the TMC2209 limits. - Protection: overload (110 to 150 % of rated power) and over-voltage on 5 V (5.75 to 6.75 V) both hiccup and recover by themselves. A wrong current limit on the LEDs tab will make the ring flicker, not latch the supply off.
- Start-up and ride-through: set-up 0.5 s (230 VAC) to 1.2 s (115 VAC), both rails together. Hold-up is only 18 ms at 115 VAC at full load, so a short mains dip will reset the processors.
- Inrush: 50 A cold start at 230 VAC. Use the slow-blow inlet fuse described in the README.
- Heat: 78 % efficient, about 24 W at full load, convection cooled, derating from 40 C ambient. Give it airflow; do not seal it in.
- Size: 159 x 97 x 38 mm.
- Unverified: the spec text was machine-extracted. Check the terminal numbering against the drawing before wiring.
Wiring the RD-85A to J-PWR-5V and J-PWR-12V#
The RD-85A has a 7-position screw terminal block: AC L, AC N, FG (earth), then the DC side with one common (COM), +V2 (12 V) and +V1 (5 V). The two outputs share COM, which matches the board's single ground.
| RD-85A terminal | Goes to | Wire |
|---|---|---|
| +V1 (5 V) | the 7.5 A inline fuse, then J-PWR-5V pins 1 and 3 (two wires after the fuse, one per pin) | 14 or 16 AWG to the fuse, 16 AWG each after it |
| COM | J-PWR-5V pins 2 and 4 (one wire each) and J-PWR-12V pin 2 | 16 AWG for the 5 V pair, 22 AWG for the 12 V lead (or one 16 AWG per terminal screw) |
| +V2 (12 V) | J-PWR-12V pin 1 | 22 AWG |
| FG | mains earth, and the enclosure | 18 AWG |
- 5 V fuse: one 7.5 A ATO/ATC blade fuse in a sealed inline holder (14 or 16 AWG leads), on a single red lead from +V1, as close to the terminal as it will go. After the fuse, split into the two 16 AWG wires to pins 1 and 3 (a lever connector rated 20 A or more, or a crimped splice). Use one fuse before the split, not one per wire: two in parallel act as a 15 A fuse. The normal load is about 4.6 A (about 60 % of the rating, so it won't age-trip). It blows on a short in the harness, the connectors or either board, protects the 16 AWG and 18 AWG wires, and caps each Mini-Fit pin at about 3.75 A. It is not the ring's current limit (the LED engine is), and it does not see a 12 V wire crimped into the 5 V plug. About $1 to $2 for the holder, fuse and splice.
- Crimp the 5 V harness to Mini-Fit Jr terminals (5557 housing) and the 12 V lead to JST SXH-001T-P0.6 terminals (XHP-2 housing). Use ring or fork terminals at the supply's M3 screws, so no strands are exposed on a mains-adjacent block.
- Keep the 5 V and COM wires to the ring side short and twisted together; at 10 A, 100 mV of drop is only 10 mohm of wire and crimps.
- Set the 5 V trim to about 5.1 V with a meter on the supply terminals, then check at
J5with the ring at full white. The trim range is 4.75 to 5.5 V. - Run the 12 V and 5 V with the ring dark first: confirm 12 V on
J-PWR-12Vpin 1 before connecting the board. - Slow-blow fuse at the inlet: the RD-85A draws 2.5 A (115 VAC) or 1.5 A (230 VAC) at full load, so use about T3.15A at 120 V or T2A at 230 V (a sizing estimate, not from the datasheet; the 50 A inrush rules out a fast fuse).
- Ground the supply's FG terminal to the enclosure and mains earth; the spec lists 0.5 kVAC output-to-FG isolation only.
Harness build and test (before first connection)#
Q5 (a P-channel FET in the 5 V ring line) blocks a reversed 5 V feed, and the 5 V and 12 V inputs are separate connectors of different families, so a 12 V plug cannot go into the 5 V header. The remaining mistake is a wire crimped into the wrong cavity of the 5 V plug (12 V on a 5 V pin), and nothing on the board catches it. D32, the SMBJ5.0A on the ring rail, conducts from 6.4 to 7.0 V and clamps at 9.2 V at its rated surge; a board crowbar was tried and dropped, because it could not clamp much lower without tripping on a healthy supply (see the CHANGELOG). A 12 V mis-wire from a supply that can deliver several amps would damage the ring and probably D32. So the harness is tested before it meets the board, every time one is made or modified.
Colour code and labels. Use the same colours at both ends and put a printed heat-shrink label on each wire:
| Net | Colour | Pins | Wire |
|---|---|---|---|
| +5V | Red | the fuse holder, then J-PWR-5V 1 and 3 | 14 or 16 AWG to the fuse, then 16 AWG each |
| GND (COM), 5 V side | Black | J-PWR-5V 2 and 4 | 16 AWG each |
| +12V | Yellow | J-PWR-12V 1 | 22 AWG |
| GND (COM), 12 V side | Black | J-PWR-12V 2 | 22 AWG |
| Mains earth (FG) | Green/yellow | not on these connectors | 18 AWG |
Never use red for anything but +5V. Keep the harness short and twist each supply wire with a ground.
Indicator jig (optional, about 5 USD, an evening). A small perfboard with a mating 2x2 Mini-Fit Jr header and a JST XH 2-pin header, and four indicator circuits, each drawing only a few milliamps:
| Indicator | Wiring | Lights when |
|---|---|---|
| 5 V good (green) | 5 V pin 1 and pin 3 (one diode each) to a 1 kΩ and a green LED to GND | pins 1 and 3 carry about 5 V |
| 12 V good (green) | XH pin 1 to 3.3 kΩ and a green LED to GND | XH pin 1 carries about 12 V |
| 12 V on a 5 V pin (red) | 5 V pin 1 and pin 3 (one diode each) to a 6.8 V zener, 470 Ω and a red LED to GND | a 5 V pin sees more than about 8.5 V |
| Ground continuity | GND pins (5 V pins 2 and 4, XH pin 2) each to a test pad, meter reads below 0.1 Ω between them |
Reversed polarity lights nothing (the LEDs block it), so both green LEDs must be on and the red LED off. Add 4 mm test pads for +5V, +12V and GND so a meter can read the voltages. The jig is not a substitute for the meter readings below; it makes a wrong harness obvious at a glance.
Test points on the board. Thirteen pads and loops are silkscreened with what they carry; none is fitted as a part (they are not in the BOM or placement files).
| Label | Net | Where | Use |
|---|---|---|---|
| GND (three loops) | GND | top left, right of the J1-H1 socket, and beside EN | scope or meter ground; a hook probe or a wire loop clips on |
| 12V | +12V_MOTOR | left, beside D1 | supply after the input connector |
| 12V F1 | +12V_MOTOR_F1 | right of D1 | after F1: 12 V here and not at 12V means F1 has tripped (switch off, remove the fault, let it cool) |
| 3V3 | +3V3 | right of the ESP32-S3-ETH | logic supply |
| 5V | +5V_LED_RING | left, above J5 | ring supply after Q5 |
| DAT 3V3 | LED_DATA_3V3 | right of the module | GPIO18, the ring data before R18 |
| DAT, CLK | LED_DATA, LED_CLK | in the LED block right of the module | the 3.3 V data and clock at the U3/U5 inputs |
| SCL, SDA | I2C_SCL, I2C_SDA | SCL below the DAT 3V3 pad, SDA at the right edge | panel expander bus |
| EN | ENABLE | beside R23 | TMC2209 enable (low = driver on) |
| LED | LED_DATA | beside EN | 3.3 V ring data before the level shifter |
STEP, DIR and the TMC2209 UART lines run only under the plugged-in modules, so there is no pad for them: probe them on the pins of the module itself.
Checklist (supply unplugged from the mains for steps 1 and 2; use a multimeter):
- Harness, supply end disconnected.
- [ ] Continuity (below 0.1 Ω) from each plug pin to the far end of its wire:
J-PWR-5Vpins 1 and 3 to the +5V lugs,J-PWR-12Vpin 1 to the +12V lug,J-PWR-5Vpins 2 and 4 andJ-PWR-12Vpin 2 to the COM lugs. - [ ] The 12 V plug is an XH 2-pin and the 5 V plug a Mini-Fit 4-pin: neither fits the other's header (try it, unpowered).
- [ ] No continuity (no beep) between any two of: +5V group, +12V group, COM group.
- [ ] Each crimp tugs without moving (pull each wire firmly).
- [ ] Continuity (below 0.1 Ω) from each plug pin to the far end of its wire:
- Harness on the supply, mains still off.
- [ ] Terminals are tight and no strand is exposed; FG is on the enclosure and mains earth.
- [ ] Still no beep between +5V, +12V and COM at the plug.
- Supply on, plug not connected to the board. Read each at the plug, black lead on a COM pin:
- [ ]
J-PWR-5Vpins 1 and 3: 4.75 to 5.5 V, then trim to 5.10 V. Positive on the meter, not negative. - [ ]
J-PWR-12Vpin 1: 11.4 to 12.6 V, positive. - [ ] Jig: both green LEDs on, the red LED off.
- [ ]
- Supply off. Board connected, ring cable not connected.
- [ ] Plug in
J-PWR-5VandJ-PWR-12V(each keyed, fully seated, the Mini-Fit latch clicked). - [ ] Resistance between the +12V rail and GND at
C8is not a short (it rises from a low reading as the capacitors charge, then climbs above 1 kΩ).
- [ ] Plug in
- Supply on,
F1is soldered on, ring cable still off.- [ ] 12 V at
C8, 3.3 V on the+3V3rail (a pad ofC9, or any 3.3 V socket pin). - [ ] Nothing hot after a minute (fingertip on
D33, the ESP32-S3-ETH module and the TMC2209 carrier).
- [ ] 12 V at
- Ring cable check, supply off. Ring end of the cable:
- [ ] Pin-for-pin continuity from
J5to the ring'sJ1(straight through, no crossed wires). Pin 2 is +5 V on the mainboard but not connected on the ring, so it should show no continuity at the ring end. Pin 1 is unused at both ends. - [ ] Signal cable:
J-LED-SIGto the ring'sJ2, pin for pin (1 data, 2 ground, 3 clock, 4 ground), no crossed wires. - [ ] +5V and GND at the ring end are not shorted (no beep, and no steady reading below about 100 Ω).
- [ ] Pin-for-pin continuity from
- Supply on, ring cable still off.
- [ ] 5.1 V on
J5pins 5 and 6 (and pin 2, which is tied to +5 V), GND on pins 3 and 4; pin 1 is unconnected. About 0 V onJ-LED-SIGpins 1 and 3 before the firmware starts.
- [ ] 5.1 V on
- Switch off, connect both ring cables, switch on. Check the limits on the LEDs tab first (below).
- [ ] The ring stays dark at power-on (
R26), then shows the set colour. - [ ] 5 V at
J5pins 5 and 6 with the ring at full white (briefly) is above about 4.7 V.
- [ ] The ring stays dark at power-on (
- Tag the harness with the date and your initials. Any change to the harness voids the tag.
Before the first power-up with the ring, check on the LEDs tab of the settings page that the ring limit is 4500 mA and the per-LED limit 36.6 mA (the defaults, with the SK9822 current at 31). Without them full white would draw about 9.6 A, over the RD-85A's 8 A. The 4500 mA limit holds the ring to about 4.5 A, the 70% of full scale the LEDs' datasheet allows for three-colour use.
If a green LED is off or a red LED is on, stop. Do not connect the board. Re-check the crimps and which wire went into which terminal; a swapped or mis-pinned wire is far cheaper to fix on the harness than on the board.
4. Signals and control#
Main controller pin use#
| GPIO | Signal | Goes to |
|---|---|---|
| 46 | STEP | TMC2209 step input |
| 48 | DIR | TMC2209 direction input |
| 0 | ENABLE | TMC2209 enable (active low); R23 holds it high through boot |
| 47 / 15 | UART TX / RX | TMC2209 one-wire serial, via R9 (1 k) |
| 18 / 2 | LED data / clock | Ring data and clock (SPI for SK9822) through U3/U5 to J-LED-SIG |
| 17 / 16 | I2C SDA / SCL | TCA9555 expander |
| 38 / 39 | Main encoder A / B | Panel (its button is on the expander, P0_3) |
| 1 / 40 | Hue encoder A / B | Panel |
| 3 | Ring temperature | J-LED-SIG pin 5 through R66 (1 k) and C16, pulled up by R65 (10 k 1 %); ADC1_CH2 |
| 43 / 44 | Saturation encoder A / B | Panel |
| 41 / 42 | Value encoder A / B | Panel |
| 45 | Fan PWM | Q6 pulls the fan's PWM input low (inverted); undriven = fan at full speed |
| 21 | Tap button | Panel |
| 9 to 14 | Ethernet chip | Inside the ESP32-S3-ETH module |
| 19 / 20 | USB | Programming and log port |
Every pin on the ESP32-S3-ETH socket was checked against Waveshare's published pinout, and the TMC2209 sockets against their makers' pinouts.
The motor driver#
- Mode: step and direction, configured over the UART at start-up. The driver's address pins and clock are tied to ground; the carrier's trimpot is ignored because the firmware sets the current.
- Settings: 800 mA RMS (the motor is rated about 1 A), 1/32 microstepping with the driver interpolating to 256, and the quiet StealthChop mode. At 32 microsteps a full turn is 6,400 steps.
- Health checks: every 5 seconds the firmware checks the serial link and the driver's over-temperature and short-circuit flags, and restores the settings if the driver has reset.
- Boot safety: three of the control pins (GPIO 0, 45 and 46) double as the processor's boot "strapping" pins.
R23(1 k to 3.3 V) holds the enable pin (GPIO 0) high, which keeps the driver disabled from power-on until the firmware is ready. The other two, STEP and the fan PWM pin, are low at reset. This makes boot independent of whatever pull-ups the driver module has.
The lighting path#
- The main controller's LED engine draws each frame (colour, effect, beat flash, current limit), about 100 a second, and sends it to the ring as SK9822 data and clock on GPIO18 and GPIO2 (SPI, 2 MHz).
R18andR61(330 Ω) feed the two buffers.U3(data) andU5(clock) lift them from 3.3 V to 5 V (they must be the AHCT part, whose inputs accept 3.3 V as a "high"), andR63/R64(33 Ω) feedJ-LED-SIGand the signal cable.R26andR62hold both lines low while the ESP32 starts, so the ring stays dark rather than flashing. On the ring,R1andR2(470 Ω) take the lines intoD1.
The VAL knob picks one of the engine's presets (a press of its button makes it the brightness) and EXP1 a palette; HUE and SAT shift and fade the colours of whatever the preset draws (the User Guide's Presets and the knobs).
Panel controls and the expander#
- The four encoders and the tap button go straight to processor pins, and the encoders are read by interrupts so fast turning isn't missed.
- The main, hue, saturation and value push buttons are on the TCA9555 expander, because the socket has no spare pins (the main encoder's button is there so GPIO3 can read the ring thermistor). They are read by polling every 20 ms.
- The expander also carries three spare encoder headers (
J-ENC-EXP1to3; the third has no push-button channel). The current firmware does not read them. The expander's spare pins (P0_4,P0_7,P1_7) are inputs, not brought out. - Static protection. Every panel signal pin goes through a 1 k resistor, with a small TVS diode to ground on the connector side, so a spark from a person touching the panel wiring is clamped before it reaches a processor pin. Each encoder's 3.3 V supply pin has a 100 Ω resistor in series, and the LED ring's 5 V supply has its own TVS (
D32) besideJ5. - Encoder modules are the common KY-040 type. Their pull-ups are fed from 3.3 V, never 5 V, because the lines go straight into 3.3 V-only inputs.
- GPIO 43 (saturation encoder A) is also the processor's boot-log output; at worst a closed encoder contact shorts it to ground for a few milliseconds during a reset, which the pin tolerates.
Encoder header pin order#
All seven encoder headers use the same five pins, in this order:
| Pin | 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|---|
| Signal | +3V3 | SW (push) | DT | CLK | GND |
(The board is silkscreened V, S, D, C, G.) The tap button header has two pins: GND and TAP. Suggested panel wire colours: main encoder blue, hue red, saturation green, value yellow, buttons orange, ground black.
Network#
Wired Ethernet comes from the W5500 chip on the ESP32-S3-ETH module. Wi-Fi is the module's own 2.4 GHz radio. Both are active at once and share the same OSC port and web pages.
5. Connector reference#
| Ref | Connector | Use |
|---|---|---|
J-PWR-5V | Molex Mini-Fit Jr, 4 pin (2×2) | 5 V in: pins 1 and 3 +5 V, pins 2 and 4 GND (see above) |
J-PWR-12V | JST XH, 2 pin (B2B-XH-A) | 12 V in: pin 1 +12 V, pin 2 GND (see above) |
J3 | JST-XH, 4 pin | Motor: 1 A+, 2 A−, 3 B+, 4 B− (pins 1+2 are one coil, 3+4 the other) |
J5 | JST VH, 4 pin, vertical (B4P-VH), 3.96 mm | LED ring power: 1 and 2 +5 V, 3 and 4 ground |
J-LED-SIG | JST XH, 5 pin (B5B-XH-A), 2.5 mm | LED ring signal: 1 data, 2 ground, 3 clock, 4 ground (5 V), 5 ring thermistor |
J1-H1, J1-H2 | Two 20-pin sockets (1 × 20 each), 2.54 mm | ESP32-S3-ETH |
J2-MODE, J2-MOTOR | 8-pin sockets, 2.54 mm | TMC2209 driver module |
J-ENC-MAIN, -HUE, -SAT, -VAL | 5-pin headers | The four panel encoders |
J-ENC-EXP1 to 3 | 5-pin headers | Expansion encoders: EXP1 palette, EXP2 effect speed, EXP3 spare |
J-BTN-TAP | 2-pin header | Tap button |
J-FAN | 4-pin keyed header (KK254 style) | 4-wire 12 V fan (not 5 V): 1 ground, 2 +12 V, 3 tach (to the expander, P0_6, through 4.7 k), 4 PWM. Powered straight from the 12 V motor rail |
The motor connector follows the common stepper wiring, so a motor cable wired black, green, red, blue (A+, A−, B+, B−) plugs straight in. If the platter turns the wrong way, swap two wires of one coil, or tick Reverse motor direction on the settings page.
6. The LED ring board#
The ring board is the second of the project's two printed circuit boards and lives in this repository (kicad_led_ring_offset/, its own KiCad project), so the repository holds every part of the physical build. It is fixed near the top of the case and does not turn with the platter.
| Size | 203.2 x 203.2 mm (8 inch), two layers; 1 oz copper (JLCPCB's default), with the 5 V harness fuse |
| LEDs | 178 x SK9822-A (OPSCO, APA102-type with data and clock, 5050 6-pin package, RGB, 5 V with a 5.3 V maximum, 27 kHz PWM so it films without flicker), on a 12.7 mm (0.5 inch) pitch in an offset "brick" pattern, wired as one long chain (D1 at the top to D178 at the bottom) |
| Per LED | One 100 nF capacitor each (178 in total), on the top side beside its LED: every part is on the top, so JLCPCB assembles one side only |
| Other parts | CP1, a 1,000 uF 16 V surface-mount bulk capacitor (D10 x L10.2); R1 and R2, 470 ohm in series with the data and clock inputs (the datasheet asks for both); TH1, a 10 k NTC (Murata NCP18XH103F03RB, B 3434 K, 0603) on the top side just inside the inner LEDs, for the ring temperature; four M3 mounting holes |
| Connectors | J1, JST VH 4 pin, side entry (B4PS-VH), in the bottom-right corner about 4 mm in from the bottom edge, with its opening toward the left: power, pin-for-pin the same as the mainboard's J5. J2, JST XH 5 pin (B5B-XH-A): data, clock and the thermistor, pin-for-pin the same as the mainboard's J-LED-SIG |
| Current | 18 mA per colour at the full 5-bit current field (31, the firmware default), 12.2 mA at the maker's recommended 22. The firmware holds each LED to 36.6 mA (full white at field 22, the maker's heat limit), so single colours run at the full 18 mA and white at about 68%; full white on every LED would be 9.6 A at 31 and 6.5 A at 22. The LED engine's limiter holds it to about 4.5 A, the 70% of full scale the datasheet allows for three-colour use |
| Mounting | Four M3 holes on a 183.8 mm square, fixed near the top of the case; does not rotate with the platter. An aluminium heat plate goes under it (see the enclosure notes, enclosure/MOTOR_MOUNT.md): only J1 and J2 have pins through the board, so the plate needs one closed window there |
| Check status | Design-rule check with schematic parity: 0 violations, 0 unconnected, 0 parity issues. Electrical-rule check: 0 |
Cables to the mainboard#
Two straight-through cables: a four-wire power harness (JST VHR-4N housings and SVH-41T-P1.1 crimps, 16-18 AWG, at both ends) from J5 on the mainboard to J1 on the ring, and a five-wire signal cable (JST XHP-5 housings) from J-LED-SIG to J2, each signal beside a ground and the thermistor on pin 5. No crossed wiring or adapter is needed. Keep the signal cable away from the motor cable.
| Pin | Mainboard J5 | Ring J1 |
|---|---|---|
| 1, 2 | +5 V ring supply | +5 V |
| 3, 4 | ground | ground |
| Pin | Mainboard J-LED-SIG | Ring J2 |
|---|---|---|
| 1 | LED_DATA_OUT (5 V data from U3 through R63) | LED_DATA_RAW, through R1 (470 ohm) to D1 SDI |
| 2, 4 | ground | ground |
| 3 | LED_CLK_OUT (5 V clock from U5 through R64) | LED_CLK_RAW, through R2 (470 ohm) to D1 CKI |
| 5 | NTC_RING_J: R65 10 k 1 % pull-up to +3V3, D34 ESD clamp, then R66 1 k / C16 to GPIO3 | NTC_RING, TH1 (10 k NTC) to ground |
Wire sizes.
- Power harness (
J5toJ1): 16 or 18 AWG, all four positions, as short as the case allows (about 0.5 m or less). JST VH is rated 10 A per pin with 16 AWG; at the 4.5 A limit each pin carries about 2.3 A. - Signal cable (
J-LED-SIGtoJ2): 22 to 24 AWG, all five wires. Twist each signal with its ground, or keep the four wires together, and route it away from the motor cable.
The signal cable's two grounds sit in parallel with the power harness's grounds, so they carry part of the ring's return current: about 15 to 25 %, or about 1 A at the 4.5 A limit. That is harmless at 22 to 24 AWG. With thinner wire, a power plug whose ground pins are not fully home would push the whole ring current through the signal cable. Always plug and unplug both cables with the power off.
Voltage drop and brightness at the platter#
These figures are simulated or estimated, not measured.
Ring copper. The ring's own copper was modelled from the filled pours, with every LED drawing the same current. At 1 oz the worst LED (D1, farthest from J1) sees about 8 mV of drop at 4.5 A, counting +5 V and ground together (2 oz would halve it for about $3 more per board at 50 to 100 boards, roughly double the bare board). The busiest copper carries about 1.4 A per mm of width at 9.6 A, and 1.4 A per mm is still inside 1 oz (IPC-2221 gives about 2.4 A for a 1 mm external 1 oz track at a 10 °C rise). J1's pads join the pours solidly, with no thermal-relief spokes, so there is no narrow neck at the connector. A fault's current is capped by the 7.5 A harness fuse (section 3).
Whole path at the 4.5 A limit. Most of the loss is in contacts and wire, not copper:
| Part of the path | At 4.5 A |
|---|---|
| Mainboard copper | about 12 mV |
Q5 | about 27 mV |
| Mated connector pairs (the Mini-Fit input, two VH pins each way on the ring cable) | up to about 135 mV at maximum contact resistance (about half that typically) |
| 0.5 m of 18 AWG harness | about 47 mV |
From a 5.1 V supply the LEDs see 4.86 V or more. Do not raise the supply to make up the drop: the SK9822's limit is 5.3 V, and it would see the full supply whenever the ring is dark.
Brightness at the platter. These are estimates from the datasheets' typical luminous intensity, which varies by about ±30 % between parts. The 1/4 in acrylic platter is 1 in above the LEDs; 69 % transmission at 1/8 in works out to about 52 % at 1/4 in. About 92 % of the ring's light reaches the platter. Inside 90 mm of the centre, the platter top is lit evenly to within about 0.64 (darkest to brightest); outside about 110 mm it gets only about 18 % of the centre's light, because the LEDs end at a 96 mm radius.
| Platter top, cd/m² (r < 90 mm) | White | Red | Green | Blue |
|---|---|---|---|---|
| SK9822-A, field 31, per-LED limit 36.6 mA (default) | about 2,460 (4.5 A) | about 1,350 | about 3,180 | about 730 |
| SK9822-A, field 22 | about 2,460 (4.5 A) | about 915 | about 2,150 | about 490 |
| SKC6812RV ring (archived), for comparison | about 3,150 (4.5 A) | about 990 | about 2,890 | about 600 |
For scale, a phone screen is 500 to 1,000 cd/m² and an indoor LED video wall 800 to 1,500. White is set by the 4.5 A limit, and the SK9822-A gives about 20 % less light per amp than the SKC6812RV. Single colours draw a third of white's current (3.2 A at field 31), so the ring limit does not hold them, and they are where the SK9822-A is brighter.
The right-angle header was chosen for the ring so the cable enters from the side and fits the low mounting location; the mainboard uses a vertical header.
Strain relief at J1. The ring hangs from the lid on four standoffs, which easily carry its own weight (about 190 g). The load to guard against is the harness: a stiff four-wire cable carrying up to about 7 A pulls on a side-entry connector near the board edge, and plugging and unplugging it pushes there too. Clamp or tie the cable to the tray or the lid a few centimetres from J1, with a loop of slack between the clamp and the connector, so the board never carries the cable's weight or stiffness. When fitting the ring, put all four standoff screws in loosely and then tighten them evenly, so a slightly bowed board is not pulled flat against its 0603 capacitors. On the board, the data line (J1 pin 1, the one thin trace at the connector) now leaves its pad straight up, away from the cable's pull, and tapers from 0.5 mm to 0.2 mm over about 12 mm, so a tug on the connector does not load a thin neck at the pad. (A straight connector on the back was considered and not adopted: its plug stands 15 to 20 mm off the board, which gives a sideways pull about three times the leverage, and through-hole parts on the bottom side are not part of JLCPCB's normal through-hole assembly.)
Layout and power copper#
- Data chain: one long chain of 178 LEDs. The jump from
D89toD90goes around the centre hole on the bottom layer as a routed track. - Power: +5 V is a copper pour on the top layer and ground a pour on the bottom layer, not traces; the board has 388 vias and 926 track segments, 0.2 mm wide except the 0.3 mm capacitor ground stubs and the tapered data entry at
J1. A simulation of the voltage drop to the farthest LED came out under 12 mV (not measured). - Power in: the mainboard side carries the same current through two connector pins each for +5 V and ground (fused at the supply, 7.5 A; see section 3).
Parts and ordering#
| Part | Reference | LCSC | JLCPCB tier | Qty |
|---|---|---|---|---|
| SK9822-A 5050 clocked RGB LED (OPSCO, 27 kHz PWM, pin 1 = SDI, 2 = CKI, 3 = GND, 4 = VDD, 5 = CKO, 6 = SDO, checked against the maker's datasheet on 2026-11-09) | D1 to D178 | C5378730 | Extended | 178 |
| 100 nF 0603 X7R, 50 V | C1 to C178 | C14663 | Basic | 178 |
| 470 ohm 0603, 1 % | R1, R2 | C23179 | Basic | 2 |
| 1,000 uF 16 V SMD electrolytic, D10 x L10.2 (ROQANG RVT1C102M1010) | CP1 | C72470 | not checked | 1 |
| 10 k NTC 0603, 1 %, B 3434 K (Murata NCP18XH103F03RB) | TH1 | C13564 | Extended | 1 |
| JST VH 4 pin, side entry (B4PS-VH) | J1 | C157996 | Extended | 1 |
| JST XH 5 pin, vertical (B5B-XH-A) | J2 | C157991 | Extended | 1 |
- Assembly scope: 360 surface-mount parts (LEDs, capacitors including
CP1,R1,R2,TH1) plus two through-hole parts, the connectorsJ1andJ2. Both have matching JLCPCB wave-solder equivalents, so full assembly needs no hand-soldering. UploadLEDRing_BOM_SMD.csvandLEDRing_CPL_SMD.csv(360 rows) for surface-mount only, or the_FULLpair (362 rows) for everything. - Component cost: about $15.58 a board at 1 board, $13.55 at 10 and $11.36 at 100 (LCSC prices of 2026-11-13,
jlc_export/ring_bom_cost.csv; this excludes JLCPCB's per-order assembly and setup fee, and will drift). - Stock (2026-11-10): the SK9822-A has about 17k at JLCPCB (enough for about 95 rings) from one maker; re-check at upload. OPSCO's plain SK9822 (C2829089, about 92k) is a fallback: same footprint and price, BGR colour order; film a sample first, as older SK9822s ran their PWM at 4.7 kHz instead of 27 kHz. The CPL turns every LED 180 degrees from KiCad's rotation to match JLCPCB's footprint (
tools/check_cpl_rotation.py). - Before ordering: leave the copper at 1 oz (the default); check the LED pinout above if the part is ever substituted; run JLCPCB's BOM upload for a final live stock check.
The Gerbers, BOM, placement files and cost roll-up are in kicad_led_ring_offset/jlc_export/, generated by kicad_led_ring_offset/tools/build_jlc_assembly.py (re-run it after any board change).
Two earlier comparison layouts (a plain square grid and a true hexagonal packing, neither fully routed) remain in the separate MegaMagicTurntable repository as design history; this offset layout is the one with real order files.
7. Motor and mechanics#
- Recommended motor: StepperOnline 17HS08-1004S: NEMA 17, 1.8° per step, 1 A per phase, 3.7 Ω, 4.5 mH, 16 N·cm holding torque, 21.5 mm body, 400 mm leads (black, green, red, blue = A+, A−, B+, B−). It is a short ("pancake") motor, which is enough torque for a light platter. A heavy platter would justify a full-length NEMA 17 (40 to 60 N·cm); the electronics suit either.
- Coupling: a flexible shaft coupler joins motor and platter directly. There is no gearbox, so platter inertia is felt straight at the motor. This is why every speed change is ramped.
- Speed: one revolution per 12 beats; default top speed 17 RPM (adjustable). At 1/32 microstepping the platter needs 6,400 steps per turn.
- Layout constraints on the mainboard: the bulk capacitors
C8andC11are 7.7 mm tall and fit between the two plug-in modules, so check clearance if you substitute taller parts.
8. Current, heat and protection notes#
- Ring current path. The 5 V route from the power connector through
Q5toJ5is carried by copper pours 6.5 mm wide or more at the narrowest point, with the return on a full bottom-layer ground plane. The power connector and ring connector each use two pins per supply, so each pin carries about 3.3 A at full white (2.3 A at the LED engine's limit). - TMC2209 heat. Fit a heatsink on the module; the maker calls for heat dissipation.
- Enclosure heat. The LED ring is the main heat source: about 3.9 W per amp of ring current. The other parts add about 7 W (motor 3 to 4.5 W). For the earlier 14 × 17 × 2 in plywood box (not redone for the current 6 mm birch box, about 13.3 × 10.7 × 2.7 in inside, which probably runs hotter) in a 43 °C (110 °F) room, a closed box holds only about 2 A average ring current (3 A with generous vents); high brightness for hours needs about 6 to 15 CFM of forced air, which one slow 120 mm fan in the bottom panel can provide. The numbers are estimates, so measure first: the Status tab, the log and
/statusreport the main processor's own temperature. The board has a fan header (J-FAN) whose speed follows that temperature between two settings you can change on the Motor tab; if the firmware stops, the fan runs at full speed. - Fuses.
F1(a 2 A hold resettable fuse, 1812, rated 16 V) protects the 12 V side; a 7.5 A blade fuse in the harness at the supply protects the 5 V side (section 3).Q5(SP30P03NK) blocks reverse polarity on the 5 V side; it loses at most about 0.32 W at the ring's 7.3 A worst case (6 mΩ maximum at 4.5 V gate drive, hotter at temperature), and about 0.12 W at the LED engine's 4.5 A limit. There is no overvoltage crowbar: the connectors are keyed and of different families, and the harness is tested before it meets the board (section 3). The RD-85A's overload protection is 110 to 150 % of its total rated power (88 W), not a 5 V current limit: on the 5 V output that is roughly 20 A or more, and the current-range figures differ between datasheet copies (Mean Well RD-85 datasheet). That protects the supply, not the wiring, hence the harness fuse. The ring's normal limit is still the LED engine's current limiter (about 4.5 A): the 9.6 A of an unlimited full white is too little over 7.5 A to blow the fuse quickly, and the wiring, connectors and copper carry it. - Voltage spikes.
D5(SMBJ15A) starts to conduct at about 16.7 V and clamps at about 24.4 V at its rated surge current: below the TMC2209's 29 V limit, the 35 V bulk capacitorsC8andC11. Running the motor rail at 12 V rather than 24 V is what makes this possible. Use a regulated 12 V supply; an adjustable one should stay between 12 and 13 V. Still never hot-plug the power connector. - Copper and voltage drop (simulated, not measured). The mainboard is ordered at 1 oz. Ring +5 V path from the power connector to
J5: about 2.8 mΩ of copper at 1 oz, 13 mV at the 4.5 A limit; ground return about 2.4 mΩ, 11 mV. IPC-2221 (external, 1 oz) gives the narrowest point, 6.5 mm wide, about 9.2 A at a 10 °C rise and 12.5 A at 20 °C, both above the 7.5 A harness fuse. 12 V motor path: about 50 mΩ, 0.1 V at 2 A.+3V3now comes out of the module at the socket, next to its main loads. - No hot-plugging. Do not connect or disconnect the motor (
J3), the ring cables (J5,J-LED-SIG), the power connector or any of the plug-in modules with the power on. A motor unplugged live produces a voltage spike that can destroy the TMC2209 (the module's maker says the same about the module itself), and the ring cable carries up to about 7 A. TheD5clamp on the 12 V rail is not designed for this. - Logic supply.
D33(SS34) feedsU3/U5and the module'sVSYSfrom+5V_LED_PSU, so they see about 4.7-4.8 V from a 5.1 V supply (the 74AHCT works from 4.5 V, the module's buck from 4 V) and a reversed supply is blocked. Not yet tested on hardware. - Ring temperature.
TH1on the ring (10 k NTC to ground) againstR65(10 k 1 % to +3V3) on the mainboard: half of 3.3 V at 25 °C, read on GPIO3 throughR66/C16every 2 s. The firmware runs the fan from it first and then lowers the ring current limit (README, Heat and ventilation); an open or shorted sensor is reported and handled.
9. Manufacturing and files#
| Item | Where |
|---|---|
| Schematic (sources) | kicad_mainboard/*.kicad_sch, rendered to Mainboard_schematic.pdf |
| PCB | kicad_mainboard/Mainboard.kicad_pcb, renders Mainboard_render_top.png and _bottom.png |
| Manufacturing files | kicad_mainboard/jlc_export/: Gerbers and drill, plus bills of materials and part-placement files in two versions (surface-mount only, or full assembly) |
| Ring board | kicad_led_ring_offset/ (KiCad project, PDFs, reports) with its own jlc_export/ and tools/build_jlc_assembly.py (section 6) |
| Check reports | erc_report.rpt (electrical rules) and drc_report.rpt (layout rules), in each KiCad folder |
| Part-number tool | kicad_mainboard/tools/build_jlc_assembly.py, which rebuilds the bills of materials from the board |
| Test points | kicad_mainboard/testpoints.kicad_sch; tools/add_test_points.py places the pads on the board |
Ordering from JLCPCB. Surface-mount only: 86 parts, 254 solder joints. Full assembly (through-hole parts too): 104 parts, 370 joints (counted from the files by tools/build_jlc_assembly.py; see jlc_export/README.md). Every part has an LCSC number (JLCPCB re-checks stock when you upload). Notable ones: expander U1 TCA9555PWR C465732, data buffer U3 C7484, TVS D5 C113988, bulk capacitors C6, C8 and C11 C176683 (an "extended" part: confirm stock when ordering).
Fuses. The board has no blade-fuse clips. F1 is a soldered resettable fuse (RUILON C20812, about $0.09) and the 5 V fuse is a standard 7.5 A ATO blade fuse in an inline holder in the harness (section 3), bought with the harness parts, not from JLCPCB. A through-hole ATO holder on the board was considered and not adopted: the only well-stocked one (Littelfuse 178.6165.0002, C207061) costs about $1.91 each at 100.
Ring board. 359 surface-mount parts plus three through-hole parts, about $18 of components (section 6).
Before ordering the board, check:
- Both boards at 1 oz copper (JLCPCB's default).
- In JLCPCB's placement preview, the orientation of
C11,Q5andU1(TSSOP-24, CPL rotation set from JLCPCB's usual TSSOP drawing, not looked up) looks right. - You have the inline holder and 7.5 A ATO fuses for the 5 V harness.
10. Verification status and limits#
Checked on the computer
- Both boards pass design-rule checks (no violations, nothing unrouted) and each matches its schematic exactly. Both schematics pass electrical-rule checks.
- Socket pin assignments match the manufacturers' published pinouts.
- The board meets JLCPCB's two-layer manufacturing limits (smallest hole 0.3 mm, narrowest track 0.2 mm).
- The speed-control logic has automated tests (
tests/), and the firmware builds with no warnings.
Checked on a bench unit. A standalone ESP32-S3-ETH running the current firmware boots, joins Wi-Fi, announces liquidturntable.local and serves its web pages. The automatic renaming of a taken hostname was tested against a name owned by a PC on the network: the unit detected the clash and announced itself as -1.
Not yet verified. No fully assembled mainboard has been powered up yet. Still to confirm on real hardware: the motor driver link and motor behaviour, the boot straps with the driver module fitted, the LED engine and ring, encoder feel, and the fuse clip fit with real fuses. The project README lists these under "Open items".
Known limits
- The three spare encoder headers are wired but not used by the firmware.
- Wi-Fi shares the 3.3 V rail with the wired network and the main controller's other loads; its power is capped to keep the rail within budget.
- The panel and ring cabling are made by hand. Check the pin order on the silkscreen, not on the connectors' descriptions in text.